Description
KHR10032 Excavator Controller Repair Service
KHR10032 Excavator Controller Repair is a specialised electronic repair service offered by Autolectronix for the KHR100xx series ECU controllers used in a wide range of Sumitomo, Case, and Link-Belt excavators.
These controllers are responsible for managing critical machine systems including engine control communication, hydraulic pump management, sensor inputs, actuator outputs, and overall machine safety logic. When the controller develops a fault, it can cause serious operational problems and in many cases can stop the excavator from operating completely.
At Autolectronix, we offer professional diagnostic testing, electronic repair, and controller cloning services for the KHR10032 excavator ECU and other controllers in the KHR100xx series.
Rather than replacing the controller with an expensive new unit, our repair service allows equipment owners, workshops, and plant operators to restore the original controller at a fraction of the replacement cost.
Common Faults – KHR10032 Excavator Controller
Over time, these controllers can develop internal electronic faults due to heat, vibration, electrical spikes, and environmental conditions commonly found in construction and mining equipment.
Some of the most common issues we see with the KHR10032 controller include:
• Excavator will not start or crank
• Intermittent engine shutdowns
• Hydraulic system not responding correctly
• Communication faults between engine ECU and controller
• Error codes appearing on the machine display
• Sensors reading incorrectly or not detected
• Pump control faults or hydraulic performance problems
• Machine stuck in limp mode
• CAN communication failures
• Internal PCB corrosion or water damage
Because these controllers are often mounted in high vibration environments, we also commonly find:
• Broken solder joints
• Failed power supply circuits
• Damaged driver components
• Memory corruption
Our technicians perform detailed bench testing and board-level diagnostics to identify the exact cause of failure.
Excavator Models Using the KHR10032 Controller
The KHR10032 ECU is used across a number of excavator platforms including machines built by Sumitomo, Case, and Link-Belt.
Sumitomo Excavators
SH130-5, SH160-5, SH180-5, SH200-5, SH210-5, SH220-5, SH240-5, SH300-5, SH330-5, SH350-5, SH360-5, SH380-5, SH450-5, SH460-5, SH480-5, SH700-5, SH800-5
Case Excavators
CX130B, CX160B, CX180B, CX210B, CX220B, CX230B, CX240B, CX290B, CX300B, CX330B, CX350B, CX360B, CX370B, CX380B, CX450B, CX460B, CX470B, CX490B, CX500B, CX700B, CX800B
Link-Belt Excavators
LBX130X2, LBX210X2, LBX240X2, LBX300X2, LBX350X3, LBX360X2
KHR100xx Controller Series
Autolectronix can also repair controllers within the KHR100xx ECU family, including:
KHR10021, KHR10022, KHR10023, KHR10024, KHR10025, KHR10026, KHR10027, KHR10028, KHR10029, KHR10030, KHR10031, KHR10032, KHR10033, KHR10034, KHR10035, KHR10036, KHR10037
Even if the part number is slightly different, the controller hardware is often very similar and repairable.
Why Choose Autolectronix?
Autolectronix specialises in electronic control unit repair for heavy equipment, trucks, buses, and construction machinery.
Our services include:
• Advanced ECU diagnostics
• Board level electronic repair
• Microprocessor and BGA repair
• ECU cloning and data recovery
• Bench simulation testing
All repairs are carried out by experienced technicians with specialist equipment.
Most repairs include a 3-month warranty, subject to installation by a qualified technician.
Contact Autolectronix
If you have a faulty KHR10032 excavator controller, we can help.
Email: sales@autolectronix.co.za
Phone: +27 31 700 1420
Ship your controller to our workshop for professional testing and repair.